Arduino + Raspberry= Weather station with webcam (Part Two: the meteo data acquisition)

Hi geek boys and girls!

I hope you passed a very nice Easter holidays. Unfortunately I had the flu during these days…so no great funny time for me! 😦

…But I spent some time developing my weather station (I wrot the code for meteo data acquisition, and then I succesfully connected to the Raspberry a webcam and also a internet dongle for the remote access to the weather station).

 

In this post I will talk about the meteo data acquisition from Arduino and the consequent data trasmission from Arduino to Raspberry via I2C (see my previous post in order to activate the I2C link).

I decided, after some unfruitful (or simply too diffcult to implement) experiment with analog sensors, to use only digital sensors to acquire with Arduino temperature, barometric pressure and relative umidity. So I bought these sensors from Robot Italy (my preferred online store for embedded resources… as you know I love all italian products/services 😉 ):

 

This is the final circuit I’ve realized after some very basic integration test (click on the image for the zoom):

Centralina_meteo_v2_bbNote that I used a resistor of 4.7 KOhm instead 5 KOhm, as suggested on the DHT11 datasheet.

Ok, now it’s time to code some litttle skecth. Let’s start with Arduino.

In order to communicate with DHT11 and with MPL115A1 I used two well known libraries.

I took the DHT11 library from Arduino Playground and I took the MPL115A1 lib from the github of SMacarena (great appreciation for these very good works, and my sincere thanks to the authors 😉 ).

After some cut/paste/washing/ironing/rewashing and some other (not too many,you know me! ;-)) tests, this is the final Arduino code for the meteo data acquisition from sensors:

 

#include <SPI.h>
#include <MPL115A1.h>
#include <dht11.h>
#include <Wire.h> //I2C library

#define __DEBUG__ //note: I used for debug a ht1632c led display
                  //If you can't/don't use it, undef this macro! :-)
#ifdef __DEBUG__
#include <ht1632c.h>

//debug display
ht1632c dotmatrix = ht1632c(&PORTD, 7, 6, 4, 5, GEOM_32x16, 2);
#endif

//i2c settings
#define SLAVE_ADDRESS 0x04
int number_command = 0;
float value_to_send=0.0;

//I2C commands
#define TEMP 1
#define HUMI 2
#define PRES 3
#define DEW 4

//out pint for DHT11 sensor
#define DHT11PIN 2

//sensors
MPL115A1 Pressure_sensor;
dht11 DHT11_sensor;

//current atmo values
float current_pressure=0.0;
float current_humidity=0.0;
float current_temperature=0.0;
double current_dewpoint=0.0;

void setup() {
  //serial setup
  Serial.begin(115200);
  //initialize pressure sensor
  Pressure_sensor.begin();

  // initialize i2c as slave
  Wire.begin(SLAVE_ADDRESS);

  // define callbacks for i2c communication
  Wire.onReceive(receiveData);
  Wire.onRequest(sendData);
#ifdef __DEBUG__
  dotmatrix.clear();
  dotmatrix.setfont(FONT_5x8);
#endif
}

void loop() {
  //take & save pressure values
  current_pressure = GetPressure();
  GetTemp_Humidity_DewPoint();

  //print current valueson serial ...debug (remove it if you want)!
  Serial.print(current_pressure);
  Serial.print(" hPa\n");

  Serial.print (current_humidity);
  Serial.print(" % Humidity\n");

  Serial.print (current_temperature);
  Serial.print(" °C\n");

  Serial.print (current_dewpoint);
  Serial.print(" Dew point (°C)\n");
#ifdef __DEBUG__
  dotmatrix.clear();
  char tmp[20] = "";
  //pressure
  sprintf(tmp, "P=%dhPa", (int)current_pressure);
  byte len = strlen(tmp);
  for (int i = 0; i < len; i++)
    dotmatrix.putchar(5*i, 0, tmp[i], ORANGE);

  //temperaure
  sprintf(tmp, "T=%dC", (int)current_temperature);
  len = strlen(tmp);
  for (int i = 0; i < len; i++)
  dotmatrix.putchar(5*i, 8, tmp[i], RED);
  //humidity
  sprintf(tmp, "H=%d%%", (int)current_humidity);
  len = strlen(tmp);
  for (int i = 0; i < len; i++)
     dotmatrix.putchar(32+5*i, 8, tmp[i], GREEN);
  dotmatrix.sendframe();

#endif
  //delay
  delay(5000);
}

//Acquisition functions
//from sensors
float GetPressure()
{
  float hPa = Pressure_sensor.pressure();
  return hPa;
}

void GetTemp_Humidity_DewPoint()
{
  //take & save DHT11 values (temp + rel. humidity)
  int chk = DHT11_sensor.read(DHT11PIN);
  switch (chk) //check errors
  {
    case DHTLIB_OK:
      Serial.println("read OK");

      //read values
      current_humidity=(float)(DHT11_sensor.humidity);
      current_temperature=(float)(DHT11_sensor.temperature);

      //dew point
      current_dewpoint=dewPoint(DHT11_sensor.temperature, DHT11_sensor.humidity);
    break;

    case DHTLIB_ERROR_CHECKSUM:
      Serial.println("Checksum error");
    break;
    case DHTLIB_ERROR_TIMEOUT:
      Serial.println("Time out error");
    break;

   default:
     Serial.println("Unknown error");
   break;
  }
}

//dewpoint function (taken from http://playground.arduino.cc/main/DHT11Lib)
// dewPoint function NOAA
// reference (1) : http://wahiduddin.net/calc/density_algorithms.htm
// reference (2) : http://www.colorado.edu/geography/weather_station/Geog_site/about.htm
//
double dewPoint(double celsius, double humidity)
{
  // (1) Saturation Vapor Pressure = ESGG(T)
  double RATIO = 373.15 / (273.15 + celsius);
  double RHS = -7.90298 * (RATIO - 1);
  RHS += 5.02808 * log10(RATIO);
  RHS += -1.3816e-7 * (pow(10, (11.344 * (1 - 1/RATIO ))) - 1) ;
  RHS += 8.1328e-3 * (pow(10, (-3.49149 * (RATIO - 1))) - 1) ;
  RHS += log10(1013.246);
  // factor -3 is to adjust units - Vapor Pressure SVP * humidity
  double VP = pow(10, RHS - 3) * humidity;
  // (2) DEWPOINT = F(Vapor Pressure)
  double T = log(VP/0.61078); // temp var
  return (241.88 * T) / (17.558 - T);
}

//I2C callbacks

// callback for received command
void receiveData(int byteCount)
{
  while(Wire.available()) {
    number_command = Wire.read();

    if(number_command==TEMP) { //request temperature
      value_to_send = current_temperature;
    }
    if(number_command==HUMI) { //request humidity
      value_to_send = current_humidity;
    }

    if(number_command==PRES) { //request humidity
      value_to_send = current_pressure;
    }

    if(number_command==DEW) { //request dewpoint
     value_to_send = current_dewpoint;
    }
  }
}

// callback for sending data via I2C
void sendData()
{
  //convert the float values in a vector of 4 bytes to send via i2c bus
  char vector_to_send[4];
  memcpy(vector_to_send,(char*)&(value_to_send),4);
  Wire.write(vector_to_send,4);
}

 

Write the above skecth on the Arduino UNO and power on it….on the serial shell (and/or on the led display) you will see the vaues taken from the sensors.

Ok, let’s go ahead with the correspondant Raspberry PI code (at the moment it is implemented in an interactive way). It is a little more simple than the Arduino one (it is derived from the original one, but in thsi case I manage the transmission via I2C of float numbers, mapped each one on 4 bytes):

//ML meteo lab station v2.0 Raspi side
#include <string.h>
#include <unistd.h>
#include <errno.h>
#include <stdio.h>
#include <stdlib.h>
#include <linux/i2c-dev.h>
#include <sys/ioctl.h>
#include <fcntl.h>
#include <unistd.h>

// The PiWeather board i2c address
#define ADDRESS 0x04

//commands
#define TEMP 1
#define HUMI 2
#define PRES 3
#define DEW 4

// The I2C bus: This is for V2 pi's. For V1 Model B you need i2c-0
static const char *devName = "/dev/i2c-1";

int main(int argc, char** argv) 
{
  printf("I2C: Connecting\n");
  int file;

  if ((file = open(devName, O_RDWR))< 0) {
    fprintf(stderr, "I2C: Failed to access %d\n", devName);
    exit(1);
  }

  printf("I2C: acquiring buss to 0x%x\n", ADDRESS);

  if (ioctl(file, I2C_SLAVE, ADDRESS) < 0) {
    fprintf(stderr, "I2C: Failed to acquire bus access/talk to slave 0x%x\n", ADDRESS);
    exit(1);
  }

  int command;

  for (command= 1; command<=4; command++) {
    int val;
    unsigned char cmd[16];
    //printf("Sending %d\n", val);

    cmd[0] = command;
    if (write(file, cmd, 1) == 1) {

      // As we are not talking to direct hardware but a microcontroller we
      // need to wait a short while so that it can respond.
      //
      // 1ms seems to be enough but it depends on what workload it has
      usleep(10000);

      char buf[5];
      if (read(file, buf, 4) == 4) { //read 4 byte from i2c (a float -temp, humidity etc.-)
        float value_received;

      //convert 4 bytes received into a float
      memcpy((char*)&value_received,buf,4);
      //print the results
      if (command==TEMP)
        printf("Temperature (°C)= %f\n", value_received );
      if (command==HUMI)
        printf("Humidity (%)= %f\n", value_received );
      if (command==PRES)
        printf("Pressure (hPa)= %f\n", value_received );
      if (command==DEW)
        printf("Dew Point (°C)= %f\n", value_received );
     }
   }

   // Now wait else you could crash the arduino by sending requests too fast
   usleep(10000);
  }

  close(file);
  return (EXIT_SUCCESS);
}

Compile the Raspberry program with the same old gcc -o meteo_lab meteo_lab.c , then, if Arduino is already powered on, launch the program with ./meteo_lab

You will see on the Raspberry shell the current values for temperature, relative humidity, pressure and dew point temperature acquired (and calculated, in case of the dew point temperature) by our two sensors.

….So, you can monitor in each moment your lab weather condition! 🙂

Ok, I think you are thinking it is not too much….So, in the next posts we will see how to visualize these data (with a good webcam image on the side) on a web page accessed from internet… this is much more interesting or not? 😉

Bye bye geeks, c ya soon!

 

Advertisements

4 thoughts on “Arduino + Raspberry= Weather station with webcam (Part Two: the meteo data acquisition)

  1. Pingback: Arduino and Android devices: the (not so) well known USB connection | ML's Garret Labs

  2. Pingback: Raspberry PI: A remote controlled relay using SMS messages | ML's Garret Labs

  3. Pingback: Arduino+Raspberry=Meteo station with webcam (Part Three: the webcam) | ML's Garret Labs

  4. Pingback: Arduino + Raspberry= Weather station with webcam (Part Four: the internet connection…. and the conclusion!) | ML's Garret Labs

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s